Cold-formed steel profiles · Mouzaia, Blida
C, U, Z and Sigma profiles for photovoltaic structures, light steel construction and storage racking, slit, punched and formed in our Blida plant.
Every section is cold-formed from strip slit on site. Height 60–300 mm, 90° bends, 4 mm inner radius, equal or unequal flanges.
Purlins & girts
Open lipped section for roof purlins, cladding girts and photovoltaic table rails.
Purlins & girts
Open lipped section for roof purlins, cladding girts and photovoltaic table rails.
Framing
Unlipped section for frames, trimmers, racking uprights and secondary framing.
Sleeved purlins
Opposed flanges that nest when lapped: continuous purlins over several bays, spans up to 12 m.
Load-bearing
Web stiffened by two 140° folds: the stiffest section in the range, spans up to 13 m and 4 mm thick.
Strut channel
41 × 41 mm channel with slotted web and in-turned lips, for module clamps, supports and racking connections.
Values from our catalogue, in millimetres. Select a row to show it on the drawing.
31 sections
| Designation | Web height | Top flange | Bottom flange | Lip | Thickness |
|---|---|---|---|---|---|
| 60 | 30 | 25 | 12 | 1.5 | |
| 60 | 30 | 25 | 13.1 | 2 | |
| 60 | 30 | 25 | 14.3 | 2.5 | |
| 80 | 35 | 30 | 14.5 | 1.5 | |
| 80 | 35 | 30 | 15.8 | 2 | |
| 80 | 35 | 30 | 17 | 2.5 | |
| 100 | 47 | 40 | 16 | 1 | |
| 100 | 47 | 40 | 17.1 | 1.5 | |
| 100 | 47 | 40 | 18.3 | 2 | |
| 120 | 47 | 40 | 16 | 1 | |
| 120 | 47 | 40 | 17.1 | 1.5 | |
| 120 | 47 | 40 | 18.3 | 2 | |
| 120 | 47 | 40 | 19.5 | 2.5 | |
| 150 | 47 | 40 | 16 | 1 | |
| 150 | 47 | 40 | 17.1 | 1.5 | |
| 150 | 47 | 40 | 18.3 | 2 | |
| 150 | 47 | 40 | 19.5 | 2.5 | |
| 180 | 60 | 53 | 19.4 | 1 | |
| 180 | 60 | 53 | 20.6 | 1.5 | |
| 180 | 60 | 53 | 21.8 | 2 | |
| 180 | 60 | 53 | 23 | 2.5 | |
| 200 | 72 | 65 | 23.6 | 1.5 | |
| 200 | 72 | 65 | 24.8 | 2 | |
| 200 | 72 | 65 | 26 | 2.5 | |
| 250 | 72 | 65 | 23.6 | 1.5 | |
| 250 | 72 | 65 | 24.8 | 2 | |
| 250 | 72 | 65 | 26 | 2.5 | |
| 250 | 72 | 65 | 27.2 | 3 | |
| 300 | 88 | 81 | 23.8 | 2 | |
| 300 | 88 | 81 | 25 | 2.5 | |
| 300 | 88 | 81 | 26.2 | 3 |
Catalogue range: thickness 1–3 mm, cut length 2,000–13,500 mm. Standard stock: 2 and 2.5 mm. Sizes in the sales brochure (C 80×40×12, Σ 160×50×12…) are example references.
Contact us for profiles with specific dimensions
Request a section to drawingFrom coil to cut-to-length profile, every step happens in Mouzaia, under the same dimensional control.
Step 1 of 4
Black or galvanized coils slit into strip at the exact developed width.
Holes and slots punched flat, before forming, at the pitch on your drawings.
Progressive forming on roll stands: 90° bends, 4 mm inner radius, equal or unequal flanges.
Cut to the ordered length, dimension check, then bundled by reference.
Recommended families by use. Our engineering office confirms the section against your loads.
Mounting rails and module supports on industrial and commercial roofs.
Recommended families
Uprights, beams and bracing for racks.
Recommended families
To support your steel construction, light steel structure and secondary framing projects, our engineering office helps you:
Our slitting line cuts black and galvanized coils into strips of precise width, to your requirements.
From coil slitting to cold forming: one integrated solution, one partner.
Slitting, punching, roll forming and cutting in our Mouzaia plant.
Material, tooling and scheduling under one roof: no subcontracting between steps.
Black or galvanized steel, grades S235, S275 and S355, thickness 1 to 4 mm.
Equal or unequal flanges, pre-punching and cut length to your drawings.
Sizing, section selection and execution drawings by our engineering office.
For EPCs delivering photovoltaic and industrial projects in Algeria, Huichuang Metal manufactures the profiles on your execution drawings, in country.
Call or email us with the family, thickness and quantity: we come back with a priced offer.